E.M.GROUT-C E.M.GROUT-C | Grouting

Home

Grouting

E.M.GROUT-C

NON-SHRINK CEMENT BASED GROUTING MORTAR

DESCRIPTION

E.M.GROUT-C is a non-shrink cementitious ready-mix grout with 65 MPa compressive strength. Due to the special combination of E.M.GROUT-C, It is useful for filling and grouting of base plates in steel frame buildings and installation of heavy machinery.

It meets the requirements of the following standard:

ASTM C1107

Method

SURFACE PREPARATION

Surfaces should be clean sound and free from oil, grease, laitance and loose particles. Metal surfaces should also be clean and free of rust, oil, grease and contaminants.

The prepared areas should be flooded with water prior to the placement of ABAGROUT-C2 before the grout is placed. All free water should be released from the area to be grouted. There should be NO standing water present when the grout is placed.

MIXING

ABAGROUT-C2 should be mixed using a suitable mixer. For flowable consistency use a band drill and paddle with a speed of <400 R.P.M. For large works use a high shear vane grout mixer. (Drum mixers are not recommended).

The entire contents of the bag should be added to the pre-measured (2.75-3.50 litres) water while mixing.

DO NOT add more than the maximum water content.

APPLICATION

Ensure the substrate is prepared according to the manufactures recommendations. NO free water should be present in the area to be grouted. Ensure that there are sufficient air release holes for entrained air to escape.

Mortar should be continuously poured, from one side only, until the gap is completely filled. Maintain continuous head of grout when pouring.

CURING

It is necessary to cure exposed areas of grout with humidified method for at least 7 days.

Properties

Suitable for static loads
Without hardening crake
Non shrinkage
Controlled expansion
Premixed grout requires only the addition of mixing water on site
Excellent flowability
High early strength and fast loading capability

Application

Ensure the substrate is prepared according to the manufactures recommendations. NO free water should be present in the area to be grouted. Ensure that there are sufficient air release holes for entrained air to escape.
Mortar should be continuously poured, from one side only, until the gap is completely filled. Maintain continuous head of grout when pouring.
Filling and grouting of base plates in steel frame buildings
Installation of heavy machinery
Installation precast columns
Anchor bolts
All areas requiring grouting

Physical and Chemical Properties

Physical state	Powder
Color	Grey
Water by weight of grout	11 - 14 %
Specific gravity of fresh mortar	2.35 ± 0.1 g/cm³
Chloride ion	No Chloride content

Considerations

STORAGE

Shelf life: 1 year in the original package.
Storage condition: should be protected from direct sunlight and moisture.
Keep bag in the temperature range between +10°C and +30°C.
Packing: 25 kgs bags.

Protection and Safty

HEALTH AND SAFETY

This product does not contain any substances hazardous to human health and the environment. However, it should not be swallowed and contact with skin and eyes. In case of contact with
eyes, rinse immediately with plenty of water. E.M.GROUT-C is not flammable.
For further information refer to the material safety data sheet. MSDS is available at ABADGARAN website.

Other Products

E.M.GROUT-C

E.M.Epoxy Grout-1000

ABADUR-G3

ABADUR-G30

ABAGROUT-HP

ABAGROUT-C2

E.M.GROUT-CE

E.M.GROUT-CL

E.M.GROUT-CM

ABADUR-G3 LE

E.M.GROUT-C

Method

Properties

Application

Physical and Chemical Properties

Considerations

Protection and Safty

Other Products

Download

E.M.GROUT-C Data Sheet